Show location and type of all braced panels or shear walls. Print job title or description, address and assessor’s parcel number and drawing index on the cover sheet.ġ.3 Floor Plan: Show all proposed building dimensions (outside wall dimensions) and label use of each room, cross reference locations and sizes of windows and doors to window and door schedules, show electric outlets, plumbing and heating fixtures (identify furnace size), carbon monoxide, and smoke detectors. Show other relative information such as driveways, wells, septic systems, source of emergency water supply, and dimension emergency vehicle access. A separate plan and details will be required identifying protection of storm water runoff during construction (i.e. Provide adequate drainage information, e.g. Indicate finished and existing grade elevations, i.e. Dimension front, side and rear distances to property lines and between structures. dwelling area, garage area, covered porches, decks, retained square footage retained at the face of retaining walls, storage areas, basements, etc.).ġ.2 Site Plan: Show property lines, easements and new and existing building locations. local or State responsibility area) and itemized square footages of all existing, proposed, and altered building areas (e.g. All drawing sheets within the digital plan set shall be included in the same file and be identified with a unique sheet number.ġ.1 Cover Sheet: Identify all applicable codes, scope of work, type of construction, sheet index, building address, parcel number, parcel size, fire safety area (i.e. All plan views, elevations, and details shall be identified with an applicable scale and a known dimension shall be provided on the associated plan, elevation, or detail to allow a plans examiner to digitally calibrate the referenced scale. Residences which are conventionally wood framed and up to two stories in height may not need to be prepared by a licensed design professional however, the individual preparing and signing plans is responsible to be knowledgeable of all applicable codes and capable of preparing plans drawn to recognized architectural standards. All documents must be digitally sealed, signed, and dated by the person responsible for preparing them. Omission of any items in the following list may result in delay of plan check, requiring resubmission of documents or information. Preliminary review with staff is encouraged to ensure complete applications. Upload the digital plan file and separate files of all supporting documentation such as structural calculations, energy compliance forms, soil reports, etc. Flood zone – (Sonoma County Code 7B), waterways, creeks, etc.Geologic hazards – Landslides, geotechnical (soils) report.Earthquake fault – Alquist/Priolo Zones.Land use limitations – County zoning ordinances, contact Planning Division. Items to be considered at earliest possible stage of project development which could affect project: To find out if a Grading Permit is required, you must fill out and submit GRD-002 Grading Permit Questionnaire (PDF) if any part of the project comes into contact with the ground or soil. Grading Permit May Be RequiredĪ separate Grading Permit application is required if the project meets the criteria established by Chapter 11 of the Sonoma County Code. Newly constructed residential dwelling units, including accessory dwelling units (ADUs), shall be designed and constructed as all-electric dwellings. Resources available to assist with questions about the applicability of the CRC are, t he CRC, the Permit Sonoma website, the California Building Standards Commission, and Permit Sonoma Plan Check staff members.Īll applicable and referenced codes are available through the California Building Standards Commission.Īdoption and amendments to the applicable codes and regulations by the County of Sonoma (Chapter 7), as well as zoning regulations (Chapter 26) and Fire Safe Standard requirements (Chapter 13) are available on the Permit Sonoma website. Some residential structures in close proximity to known earthquake faults may not be eligible to use the CRC for the structural portion of their design. Sections 8-11 address building structural design and are applicable to non-engineered structures and non-engineered elements of partially engineered structures. They apply to all one and two-family dwellings and their accessory structures as defined by CRC R202. Sections 2-7 of this document are considered Life-Safety sections. 2022 California Green Building Standards Code (CalGreen).Full compliance is required by reference to the following adopted codes: The following is only a partial list of required checklist items.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |